For a tree you will need: • Beads of blue, green, red, yellow (or any other of your choice); • • Beads of green shades (for stand); • Wire beaded (thin); • Thick wire (for stem and branches); • • Thin, tight wire for lianas; • Teip-tape (green); • • Cutting pliers; • Round-nose pliers; • Alabaster (plaster); • PVA glue; • Water; • Milk; • Brushes for applying plaster (hard);
• Brushes for rashivaniya tree; • Gouache;. • Yarns or wires to collect wood 1) Form a trunk and branches Take 2 thick wire.. I have the length of the left wire - 32 cm, and the right one - 24 cm. We tie them with a thread (red thread in the photo) and make bends. Add 2 short branches on the sides of the right branch of our fairytale tree.
For convenience, as a stand, I temporarily used plasticine. Next, we will make vines. To do this, take the wire of the required length and wrap it with a tape tape.We give curls to the lianas and wind them to the branches with a thread (black thread in the photo). I took a thin wire for the left creeper with a length of 38 cm, for the right bottom - 18.5 cm. And I took the wire for the two top creepers on the right. Wire for creepers should be thin, but at the same time tight, it should keep its shape well.
2) We form our "pendants". Cut the beaded wire of the required length (I cut off a length of 37-38 cm). And thread the beads, alternating colors as desired. Leave 4-5 cm of bare wire at the end. For the left branch I turned out - 39 hooks, and for the right one - 7. Also for the right branch, I cut the wire smaller.
Pletya beads on this principle, I alternate it with other colors. Having made the required number of pendants, we wind them to the left branch.
In these photos a smaller amount is made,Later I added more visyulek.
3) Now is the time to plant our tree. Take 3 short thick wires, make bends and drag them to the trunk.
Now we need a stand. Wrap it with food film.
First lay out the first layer of gypsum on it, the tree is not planted yet. In some places I put pieces of wire, for the strength of the stand. We do the gypsum solution like this: Pour some water into the container (it’s better to take half from a plastic bottle), add a little plaster and stir it thoroughly. We need the consistency of thick cream. There is no need to make a lot of solution at once, as it dries very quickly.
Now you can plant a tree.
We smear the trunk and twigs with plaster. Make the solution for the trunk and branches thinner. To dry out the gypsum solution, add a little milk to it.
I decided to make peeled bark from this side of the trunk.
To do this, in the center of the trunk, make the bark smooth, and on the sides, carefully apply the top layer of bark.
On the other sides of the trunk also apply various outlines of the bark.
With a sharp object draw a and bark relief branches.
WhenFully form the bark of the tree, leave it for a couple of days to dry out the gypsum. To make relief easier on the branches, dilute the gypsum and add more milk. Then drawing lines on branches will be more convenient. 4) Painting a tree. At first I painted the tree with brown paint, the protruding places of the bark were light brown (with a dry brush I applied paint with dipping movements). At the base of the trunk sometimes added a green color.
>img src="https://sdelaysam-svoimirukami.ru/images/10/1999-pokraska-derevca.jpg" alt="Painting the tree" title="Painting the tree">
Next we paint our stand.
With the help of gypsum stuck pebbles (7 pcs.).
Dipped with glue and sprinkled with beads of green hues.
And covered the tree with varnish.
When the varnish was dry, she made another liana. Wrapped it right branch and trunk. For this vine I used bead wire. Also wrapped it with a tape tape. Making such a tree took me 11 days, every day I spent a couple of hours. The height from the stand to the vine is 28 cm. Width is 34 cm.
Fantastic tree ready!